Four numbers, not one
Buying a rack feels simple until the first server will not fit. Height is only one of four numbers that decide whether your kit goes in: height, width, depth and weight. The one people check least is depth.
What a U is
A U (rack unit) is a height: 44.45 mm, or 1.75 inches. Rack kit is described in whole units, so a 1U server is about 44 mm tall and a 2U server about 89 mm. A rack's height is the number of U it offers, so a 12U rack holds twelve 1U devices or any mix that adds up to twelve.
The standard width is 19 inches, the width across the mounting rails, with holes in a fixed pattern. Kit sold as 19 inch rack mount fits the rails of any standard rack. The rack itself is wider outside because of the frame, so measure the space you have.
Small 10 inch racks and half width gear exist for compact labs, but they are a separate standard. Check which one a product uses before ordering.
Depth: the number that catches people out
Rack depth is the usable space from the front rails to the back. Kit varies a lot:
- Switches and patch panels are often shallow, sometimes 200 to 300 mm.
- Rack UPS units and NAS boxes are often deeper than their height suggests.
- Full servers are often 600 mm or more, and some exceed 700 mm.
The rule: measure the deepest device, add room for cables and plugs behind it, then compare with the rack's internal depth. Power and network cables need space to bend, which adds tens of millimetres at the back, and an enclosed cabinet's rear door still has to close.
Shallow racks and wall cabinets are common at home because they save space, but they exclude full depth servers. Check the depth figure in each product's specs rather than a label such as "server rack".
Open frame, enclosed or wall mount
Open frame racks are a steel frame with two or four posts. They are cheap, easy to work in and good for airflow, with no dust protection, no noise reduction and no lock. Two post frames suit light kit such as switches and patch panels. Four post frames carry servers properly.
Enclosed cabinets have side panels and a front door, usually glass or mesh. They are tidier, a little quieter and safer around children and pets. They need ventilation: mesh doors and roof fans matter, because a sealed cabinet full of servers is an oven. They are also heavier and cost more.
Wall mount cabinets hang on a wall, typically between 4U and 15U. They suit network kit and small devices in a hallway, loft or garage. Check the wall: a loaded cabinet is heavy, and plasterboard alone will not hold it. Check depth too, because many wall units are shallow.
- Spare room or garage, noise tolerated: open frame or a vented cabinet.
- Living space: enclosed, with attention to airflow and fan noise.
- Network kit only: wall mount.
Compare current rack cabinet prices by height, depth and type.
What fits in 12U, 22U and 42U
These are the usual sizes. The layouts below are planning examples, not a recommendation to fill every slot.
A 12U rack is a sensible home size, wall mounted or a small floor cabinet. A typical layout: a 1U patch panel, a 1U switch, 1U for a router or firewall, 2U for a UPS at the bottom (heavy items go low), 2U to 4U for a server or NAS, and a shelf or blanking panel to finish. It assumes shallow to medium depth kit: a full depth server in a shallow 12U cabinet is the most common mistake.
A 22U cabinet gives room for a small cluster: network kit at the top in 3U to 4U, two or three 1U or 2U servers, a 3U or 4U storage chassis, a 2U or 3U UPS at the bottom, a PDU at the rear and spare U for growth and airflow. At this size it is a floor item that will not move easily once loaded.
A 42U rack is a full height data centre rack, around two metres tall. Before buying one check it fits through the door, the ceiling height, the floor, the power available, and the heat and noise of a full rack. A UK 13 amp socket supplies about 3 kW at most, and a full rack of older servers can need more than one circuit.
Things people forget
- Blanking panels: empty gaps let hot air loop back to the front. Fill unused U.
- Rails: servers need rails or shelves. Check the rail depth range against the rack, and the hole style (square, round or threaded).
- Cable management: leave space for brush panels or cable arms. A tidy rack is easier to cool and fix.
- Weight and floor: add up the weight, especially the UPS and storage, and check the rack's load rating.
- Power: a PDU gives enough sockets and sometimes metering. Check the total against the circuit.
- Cooling: heat builds up in a small room. Think about ventilation, not only space.
- Access: leave room in front and behind to work. A hinged wall cabinet is far easier to service.
A simple way to plan
- 1List every device with its height in U, depth in mm and weight.
- 2Add the heights, then add 20 to 30 percent for growth and gaps.
- 3Take the deepest device and add room for cables.
- 4Choose the rack type from where it will live.
- 5Check ventilation, power and the floor or wall.
The rack planner does this for you: lay devices out U by U and it checks space, depth, UPS load and switch ports, with UK prices for each part.