Black Friday is 10 days and 20 hours away.See the price watchNew on the blog: UK Black Friday PC price check 2026: 22% of deals are real lows

Skip to content
All guides

Choosing a UPS for a Homelab or Home Server

Size it on watts, pick the right type, and make sure it actually shuts your servers down.

Beginner 5 min readBy Spencer BullockUpdated

Two jobs

A UPS (uninterruptible power supply) does two jobs. It keeps your kit running through a brief cut or a dip, and it gives your servers time to shut down properly when the cut is longer. The second job is the one most people forget, and it is the one that saves your data.

VA is not watts

UPS units are rated in VA (volt-amperes) and in watts. Both matter, but not equally.

  • Watts is the real power the UPS can deliver.
  • VA is apparent power, always the bigger number.

The ratio between them varies by design: two units with the same VA rating can deliver quite different wattages. Always size against the watt rating, then check VA second. If a product page gives only VA, find the watt figure in the datasheet before you buy.

To size it, add up the real draw of what you will plug in. Measure with a plug-in power meter if you can; nameplate maximums are almost always higher than real use. Then keep the load well below the UPS limit. Running near the maximum shortens battery life and cuts runtime sharply. Around half to two thirds of the watt rating is a comfortable target, and it leaves headroom for drives spinning up.

Standby, line-interactive or online

  • Standby (offline): the cheapest. Mains passes straight through and the battery takes over after a short switchover. Fine for a desktop, less so for servers.
  • Line-interactive: adds automatic voltage regulation, correcting mild over and under voltage without touching the battery. The usual choice for a homelab.
  • Online (double conversion): the inverter always powers your kit, so there is no switchover at all. It costs more, runs warmer, often has a fan that never stops, and wastes some energy as heat every hour.

For most homelabs a good line-interactive unit is right. Online makes sense for sensitive kit, unreliable mains, or when you would rather pay once than think about it. Check its efficiency and noise, because that overhead runs all day.

Sine wave matters

Cheaper units often output a stepped or simulated sine wave on battery. Plenty of kit tolerates it. Some does not, notably power supplies with active power factor correction (active PFC), which most modern server and quality desktop supplies use. They can buzz, reset or shut down on a stepped wave, at exactly the moment you need them.

If your supplies use active PFC, buy a pure sine wave UPS. The product page should state pure sine wave output on battery plainly. Compare current UPS prices by capacity, topology and form factor.

Runtime: estimating honestly

Makers publish runtime charts at various loads. Use them with three cautions.

  1. 1Charts are for a new battery. Sealed lead acid batteries lose capacity with age and are commonly replaced every three to five years.
  2. 2Runtime falls faster than load rises: doubling the load usually more than halves it.
  3. 3Do not aim for hours. The goal is time to shut down cleanly. A few minutes is usually enough for a small stack; hours need a far bigger battery or an external pack.

A simple method: measure the real load in watts, read the runtime chart at that load, take off a margin for battery age, and compare the result with how long your slowest machine takes to shut down. A NAS flushing its disks can take a minute or two, and a hypervisor with several virtual machines takes longer.

If runtime is short, cut the load first. Leave the monitor, printer and lamps off the UPS. Only the servers, the NAS, the switch and the router need it.

Outlets, form factor and noise

  • Outlets: many units have IEC C13 outlets, some have UK sockets, some both. Check the mix against your plugs: a nest of adapters on a UPS is a bad idea.
  • Tower or rack: towers are cheaper and sit on a shelf. Rack units are usually 1U or 2U for small ones, but deeper and heavier than they look. Check the depth against your rack; see rack sizes explained.
  • Noise: fans in online and larger units can be audible. If it lives in a living space, check reviews for noise.
  • Weight: batteries are heavy. A mid size UPS can outweigh a small server, so keep it low.

USB, NUT and clean shutdown

A UPS that only beeps is half a UPS. To shut machines down automatically, connect the UPS to one machine over USB (or a network card on bigger units) and run monitoring software.

NUT (Network UPS Tools) is the common open standard. A typical layout:

  1. 1Plug the UPS USB cable into one always-on machine, the NUT server: a mini PC, or a NAS that supports it.
  2. 2NUT reads battery charge, load and runtime from the UPS.
  3. 3Other machines run a NUT client and ask the server for status over the network.
  4. 4When the battery is low, or runtime drops below a threshold you set, the clients shut down. The NUT server goes last, then the UPS cuts power.

Many NAS operating systems and hypervisors support this natively or with a package. Test it: pull the mains plug on purpose and watch everything shut down. A shutdown plan you have never tested is a hope, not a plan.

Tip: Trigger shutdown on remaining runtime rather than a battery percentage, since a percentage means different things at different loads. And keep the router, switch and NUT server powered until the clients finish, or they cannot hear the order.

Sensible starting points

  • One mini PC and a switch: a small line-interactive unit.
  • A NAS and a few servers: a pure sine wave line-interactive unit sized to about half load, with NUT.
  • A rack with sensitive kit: consider an online rack unit, and plan for its noise and heat.

The rack planner adds up UPS load and estimated runtime as you place devices.

Before you buy

  1. 1Measure the real load in watts.
  2. 2Size against watts, with headroom.
  3. 3Pick line-interactive unless you have a reason for online.
  4. 4Choose pure sine wave if any supply uses active PFC.
  5. 5Read the runtime chart at your real load, and expect it to fall as the battery ages.
  6. 6Set up USB and NUT, and test the shutdown.
  7. 7Compare the same unit across shops, and note when each price was last read.

Compare UK prices